Difference between revisions of "LCDd"

From knowledgebase
Jump to navigation Jump to search
(Replaced content with "LCDd Category:log")
Tag: Replaced
 
Line 1: Line 1:
−
LCDd
+
Use the default LCDd.conf that gets installed with the lcdproc package.
 +
 
 +
Change the line
 +
{{{
 +
Driver=curses
 +
}}}
 +
to
 +
{{{
 +
Driver=imon
 +
}}}
 +
 
 +
Create a file lirc.conf in /etc/modprobe.d with the following content, this will make sure the soundgraph imon is recognized as a vfd (rather than an lcd)
 +
 
 +
{{{
 +
options lirc_imon display_type=1
 +
}}}
 +
 
 +
{{{
 +
# LCDd.conf -- configuration file for the LCDproc server daemon LCDd
 +
#
 +
# This file contains the configuration for the LCDd server.
 +
#
 +
# The format is ini-file-like. It is divided into sections that start at
 +
# markers that look like [section]. Comments are all line-based comments,
 +
# and are lines that start with '#' or ';'.
 +
#
 +
# The server has a 'central' section named [server]. For the menu there is
 +
# a section called [menu]. Further each driver has a section which
 +
# defines how the driver acts.
 +
#
 +
# The drivers are activated by specifiying them in a driver= line in the
 +
# server section, like:
 +
#
 +
#
 +
# This tells LCDd to use the curses driver.
 +
# The first driver that is loaded and is capable of output defines the
 +
# size of the display. The default driver to use is curses.
 +
# If the driver is specified using the -d <driver> command line option,
 +
# the Driver= options in the config file are ignored.
 +
#
 +
# The drivers read their own options from the respective sections.
 +
 
 +
 
 +
 
 +
## Server section with all kinds of settings for the LCDd server ##
 +
[server]
 +
 
 +
# Where can we find the driver modules ?
 +
# IMPORTANT: Make sure to change this setting to reflect your
 +
#            specific setup! Otherwise LCDd won't be able to find
 +
#            the driver modules and will thus not be able to
 +
#            function properly.
 +
# NOTE: Always place a slash as last character !
 +
DriverPath=/usr/lib/lcdproc/
 +
 
 +
# Tells the server to load the given drivers. Multiple lines can be given.
 +
# The name of the driver is case sensitive and determines the section
 +
# where to look for further configuration options of the specific driver
 +
# as well as the name of the dynamic driver module to load at runtime.
 +
# The latter one can be changed by giving af File= directive in the
 +
# driver specific section.
 +
#
 +
# The following drivers are supported:
 +
#  bayrad, CFontz, CFontz633, CFontzPacket, curses, CwLnx, ea65,
 +
#  EyeboxOne, g15, glcdlib, glk, hd44780, icp_a106, imon, imonlcd, IOWarrior,
 +
#  irman, joy, lb216, lcdm001, lcterm, lirc, lis, MD8800, ms6931, mtc_s16209x,
 +
#  MtxOrb, mx5000, NoritakeVFD, picolcd, pyramid, sed1330, sed1520, serialPOS,
 +
#  serialVFD, shuttleVFD, sli, stv5730, svga, t6963, text, tyan, ula200,
 +
#  xosd
 +
Driver=imon
 +
 
 +
# Tells the driver to bind to the given interface
 +
Bind=127.0.0.1
 +
 
 +
# Listen on this specified port; defaults to 13666.
 +
Port=13666
 +
 
 +
# Sets the reporting level; defaults to 2 (warnings and errors only).
 +
#ReportLevel=3
 +
 
 +
# Should we report to syslog instead of stderr ? [default: no; legal: yes, no]
 +
#ReportToSyslog=yes
 +
 
 +
# User to run as.  LCDd will drop its root priviledges, if any,
 +
# and run as this user instead.
 +
User=nobody
 +
 
 +
# The server will stay in the foreground if set to true.
 +
#Foreground=no
 +
 
 +
# Hello message: each entry represents a display line; default: builtin
 +
#Hello="  Welcome to"
 +
#Hello="  LCDproc!"
 +
 
 +
# GoodBye message: each entry represents a display line; default: builtin
 +
#GoodBye="Thanks for using"
 +
#GoodBye="  LCDproc!"
 +
 
 +
# Sets the default time in seconds to displays a screen.
 +
WaitTime=5
 +
 
 +
# If yes, the the serverscreen will be rotated as a usual info screen. If no,
 +
# it will be a background screen, only visible when no other screens are
 +
# active. The special value 'blank' is similar to no, but only a blank screen
 +
# is displayed. [default: on; legal: on, off, blank]
 +
#ServerScreen=no
 +
 
 +
# Set master backlight setting. If set to 'open' a client may control the
 +
# backlight for its own screens (only). [default: open; legal: off, open, on]
 +
#Backlight=open
 +
 
 +
# Set master heartbeat setting. If set to 'open' a client may control the
 +
# heartbeat for its own screens (only). [default: open; legal: off, open, on]
 +
#Heartbeat=open
 +
 
 +
# set title scrolling speed [default: 10; legal: 0-10]
 +
#TitleSpeed=10
 +
 
 +
# The "...Key=" lines define what the server does with keypresses that
 +
# don't go to any client.
 +
# These are the defaults:
 +
ToggleRotateKey=Enter
 +
PrevScreenKey=Left
 +
NextScreenKey=Right
 +
#ScrollUpKey=Up
 +
#ScrollDownKey=Down
 +
 
 +
# If you have only 4 keys, you can choose to use this:
 +
#ToggleRotateKey=Enter
 +
#PrevScreenKey=Up
 +
#NextScreenKey=Down
 +
 
 +
# If you have only 3 keys, you can choose to use this:
 +
#ToggleRotateKey=Enter
 +
#PrevScreenKey=Up
 +
 
 +
 
 +
 
 +
## The menu section. The menu is an internal LCDproc client. ##
 +
[menu]
 +
# You can configure what keys the menu should use. Note that the MenuKey
 +
# will be reserved exclusively, the others work in shared mode.
 +
 
 +
# The following works excellent with 4 keys or more.
 +
MenuKey=Escape
 +
EnterKey=Enter
 +
UpKey=Up
 +
DownKey=Down
 +
# If you have 6 keys you may define these as well
 +
#LeftKey=Left
 +
#RightKey=Right
 +
 
 +
# If you have only 3 keys, you could use something like this:
 +
#MenuKey=Escape
 +
#EnterKey=Enter
 +
#DownKey=Down
 +
 
 +
 
 +
 
 +
### Driver sections are below this line, in alphabetical order  ###
 +
 
 +
 
 +
## EMAC BayRAD driver ##
 +
[bayrad]
 +
 
 +
# Select the output device to use [default: /dev/lcd]
 +
Device=/dev/lcd
 +
 
 +
# Set the communication speed [default: 9600; legal:  1200, 2400, 9600, 19200]
 +
Speed=9600
 +
 
 +
 
 +
 
 +
## CrystalFontz driver (for CF632 & CF634) ##
 +
[CFontz]
 +
 
 +
# Select the output device to use [default: /dev/lcd]
 +
Device=/dev/ttyS0
 +
# Select the LCD size [default: 20x4]
 +
Size=20x4
 +
# Set the initial contrast [default: 560; legal: 0 - 1000]
 +
Contrast=350
 +
# Set the initial brightness [default: 1000; legal: 0 - 1000]
 +
Brightness=1000
 +
# Set the initial off-brightness [default: 0; legal: 0 - 1000]
 +
# This value is used when the display is normally
 +
# switched off in case LCDd is inactive
 +
OffBrightness=0
 +
# Set the communication speed [default: 9600; legal: 1200, 2400, 9600, 19200 or 115200]
 +
Speed=9600
 +
# Set the firmware version (New means >= 2.0) [default: no; legal: yes, no]
 +
NewFirmware=no
 +
# Reinitialize the LCD's BIOS [default: no; legal: yes, no]
 +
# normally you shouldn't need this
 +
Reboot=no
 +
 
 +
 
 +
 
 +
## CrystalFontz633 driver (for CF633 only) ##
 +
[CFontz633]
 +
 
 +
# Select the output device to use [default: /dev/lcd]
 +
Device=/dev/ttyS0
 +
# Select the LCD type (size) [default: 16x2]
 +
Size=16x2
 +
# Set the initial contrast [default: 560; legal: 0 - 1000]
 +
Contrast=350
 +
# Set the initial brightness [default: 1000; legal: 0 - 1000]
 +
Brightness=1000
 +
# Set the initial off-brightness [default: 0; legal: 0 - 1000]
 +
# This value is used when the display is normally
 +
# switched off in case LCDd is inactive
 +
OffBrightness=50
 +
# Set the communication speed [default: 9600; legal: 1200, 2400, 9600, 19200, 115200]
 +
Speed=19200
 +
# Set the firmware version (New means >= 2.0) [default: no; legal: yes, no]
 +
# Currently this flag is not in use, there is no such thing as NewFirmware. ;=)
 +
#NewFirmware=no
 +
# Reinitialize the LCD's BIOS [default: no; legal: yes, no]
 +
# I want to reboot the LCD to make sure we start from a known state
 +
Reboot=yes
 +
 
 +
 
 +
 
 +
## CrystalFontz packet driver (for CF631, CF633 & CF635) ##
 +
[CFontzPacket]
 +
 
 +
# Select the LCD model [default: 633; legal: 631, 633, 635]
 +
Model=635
 +
# Select the output device to use [default: /dev/lcd]
 +
Device=/dev/ttyUSB0
 +
# Select the LCD size [default: depending on model: 635: 20x4, 631: 20x2, 633: 16x2]
 +
Size=20x4
 +
# Set the initial contrast [default: 560; legal: 0 - 1000]
 +
Contrast=350
 +
# Set the initial brightness [default: 1000; legal: 0 - 1000]
 +
Brightness=1000
 +
# Set the initial off-brightness [default: 0; legal: 0 - 1000]
 +
# This value is used when the display is normally
 +
# switched off in case LCDd is inactive
 +
OffBrightness=50
 +
# Set the communication speed [default: 9600; legal: 1200, 2400, 9600, 19200, 115200]
 +
Speed=115200
 +
# Set the firmware version (New means >= 2.0) [default: no; legal: yes, no]
 +
# Currently this flag is not in use, there is no such thing as NewFirmware. ;=)
 +
#NewFirmware=no
 +
# Reinitialize the LCD's BIOS [default: no; legal: yes, no]
 +
# I want to reboot the LCD to make sure we start from a known state
 +
Reboot=yes
 +
 
 +
 
 +
 
 +
## Curses driver ##
 +
[curses]
 +
 
 +
# color settings
 +
# foreground color [default: blue]
 +
Foreground=blue
 +
# background color when "backlight" is off [default: cyan]
 +
Background=cyan
 +
# background color when "backlight" is on [default: red]
 +
Backlight=red
 +
 
 +
# display size [default: 20x4]
 +
Size=20x4
 +
 
 +
# What position (X,Y) to start the left top corner at...
 +
# Default: (7,7)
 +
TopLeftX=7
 +
TopLeftY=7
 +
 
 +
# use ASC symbols for icons & bars [default: no; legal, yes, no]
 +
UseACS=no
 +
 
 +
# draw Border [default: yes; legal: yes, no]
 +
DrawBorder=yes
 +
 
 +
 
 +
 
 +
## Cwlinux driver ##
 +
[CwLnx]
 +
 
 +
# Select the LCD model [default: 12232; legal: 12232, 12832, 1602]
 +
Model=12232
 +
 
 +
# Select the output device to use [default: /dev/lcd]
 +
Device=/dev/ttyUSB0
 +
 
 +
# Select the LCD size [default: depending on model: 12232: 20x4, 12832: 21x4, 1602: 16x2]
 +
Size=20x4
 +
 
 +
# Set the communication speed [default: 19200; legal: 9600, 19200]
 +
Speed=19200
 +
 
 +
# Reinitialize the LCD's BIOS [default: no; legal: yes, no]
 +
# normally you shouldn't need this
 +
Reboot=no
 +
 
 +
# If you have a keypad connected. Keypad layout is currently not
 +
# configureable from the config file.
 +
Keypad=yes
 +
 
 +
# If you have a non-standard keypad you can associate any keystrings to keys.
 +
# There are 6 input keys in the CwLnx hardware that generate characters
 +
# from 'A' to 'F'.
 +
#
 +
# The following is the built-in default mapping hardcoded in the driver.
 +
# You can leave those unchanged if you have a standard keypad.
 +
# You can change it if you want to report other keystrings or have a non
 +
# standard keypad.
 +
# KeyMap_A=Up
 +
# KeyMap_B=Down
 +
# KeyMap_C=Left
 +
# KeyMap_D=Right
 +
# KeyMap_E=Enter
 +
# KeyMap_F=Escape
 +
 
 +
# keypad_test_mode permits to test keypad assignement
 +
# Default value is no
 +
#keypad_test_mode=yes
 +
 
 +
 
 +
 
 +
## ea65 driver for the display in AOpen XC Cube AV EA65 media barebones ##
 +
[ea65]
 +
 
 +
# Device is fixed /dev/ttyS1
 +
# Width and Height are fixed 9x1
 +
 
 +
# As the VFD is self luminescent we don't have a backlight
 +
# But we can use the backlight functions to control the front LEDs
 +
# Brightness 0 to 299 -> LEDs off
 +
# Brightness 300 to 699 -> LEDs half bright
 +
# Brightness 700 to 1000 -> LEDs full bright
 +
Brightness=500
 +
# OffBrightness is the the value used for the 'backlight off' state
 +
OffBrightness=0
 +
 
 +
 
 +
 
 +
## EyeboxOne driver ##
 +
[EyeboxOne]
 +
 
 +
# Select the output device to use [default: /dev/ttyS1]
 +
#Device=/dev/cua01
 +
Device=/dev/ttyS1
 +
 
 +
# Set the display size [default: 20x4]
 +
Size=20x4
 +
 
 +
# Switch on the backlight? [default: yes]
 +
Backlight=yes
 +
 
 +
# Switch on the cursor? [default: no]
 +
Cursor=no
 +
 
 +
# Set the communication speed [default: 19200; legal: 1200, 2400, 9600, 19200]
 +
Speed=19200
 +
 
 +
# Enter Key is a \r character, so it's hardcoded in the driver
 +
LeftKey=D
 +
RightKey=C
 +
UpKey=A
 +
DownKey=B
 +
EscapeKey=P
 +
 
 +
# You can find out which key of your display sends which
 +
# character by setting keypad_test_mode to yes and running
 +
# LCDd. LCDd will output all characters it receives.
 +
# Afterwards you can modify the settings above and set
 +
# keypad_set_mode to no again.
 +
keypad_test_mode=no
 +
 
 +
 
 +
 
 +
## g15 driver for Logitech G15 Keyboard LCDs ##
 +
[g15]
 +
 
 +
# Display size (currently unused)
 +
size=20x5
 +
 
 +
 
 +
 
 +
## glcdlib meta driver for graphical LCDs ##
 +
[glcdlib]
 +
 
 +
## mandatory:
 +
 
 +
# which graphical display supported by graphlcd-base to use [default: image]
 +
# (see /etc/graphlcd.conf for possible drivers)
 +
Driver=noritake800
 +
 
 +
# no=use graphlcd bitmap fonts (they have only one size / font file)
 +
# yes=use fonts supported by FreeType2 (needs Freetype2 support in libglcdprocdriver and its dependants)
 +
UseFT2=yes
 +
 
 +
# text resolution in fixed width characters [default: 16x4]
 +
# (if it won't fit according to available physical pixel resolutioni
 +
# and the minimum available font face size in pixels, then
 +
# 'DebugBorder' will automatically be turned on)
 +
TextResolution=20x4
 +
 
 +
# path to font file to use
 +
FontFile=/usr/share/fonts/corefonts/courbd.ttf
 +
 
 +
## these only apply if UseFT2=yes:
 +
 
 +
# character encoding to use
 +
CharEncoding=iso8859-2
 +
 
 +
# minumum size in pixels in which fonts should be rendered
 +
MinFontFaceSize=7x12
 +
 
 +
## optional:
 +
Brightness=50                  # Brightness (in %) if applicable
 +
Contrast=50                    # Contrast (in %) if applicable
 +
Backlight=no                    # Backlight if applicable
 +
UpsideDown=no                  # flip image upside down
 +
Invert=no                      # invert light/dark pixels
 +
ShowDebugFrame=no              # turns on/off 1 pixel thick debugging
 +
                                # border whithin the usable text area,
 +
                                # for setting up TextResolution and
 +
                                # MinFontFaceSize (if using FT2);
 +
ShowBigBorder=no                # border around the unused area
 +
ShowThinBorder=yes              # border around the unused area
 +
PixelShiftX=0
 +
PixelShiftY=2
 +
 
 +
 
 +
 
 +
## Matrix Orbital GLK driver ##
 +
[glk]
 +
 
 +
# select the serial device to use [default: /dev/lcd]
 +
Device=/dev/lcd
 +
 
 +
# set the initial contrast value [default: 560; legal: 0 - 1000]
 +
Contrast=560
 +
 
 +
# set the serial port speed [default: 19200; legal: 9600, 19200, 38400]
 +
Speed=19200
 +
 
 +
 
 +
 
 +
## Hitachi HD44780 driver ##
 +
[hd44780]
 +
 
 +
# Select what type of connection. See documentation for types.
 +
ConnectionType=4bit
 +
 
 +
# Port where the LPT is [ususal: 0x278, 0x378 and 0x3BC]
 +
Port=0x378
 +
 
 +
# Device of the serial interface [default: /dev/lcd]
 +
Device=/dev/ttyS0
 +
 
 +
# Bitrate of the serial port (0 for interface default)
 +
Speed=0
 +
 
 +
# If you have a keypad connected.
 +
# You may also need to configure the keypad layout further on in this file.
 +
Keypad=no
 +
 
 +
# Set the initial contrast (bwctusb and lcd2usb) [default: 500; legal: 0 - 1000]
 +
Contrast=0
 +
 
 +
# Set brightness of the backlight (lcd2usb only) [default: 0; legal 0 - 1000]
 +
#Brightness=1000
 +
#OffBrightness=0
 +
 
 +
# If you have a switchable backlight.
 +
Backlight=no
 +
 
 +
# If you have the additional output port ("bargraph") and you want to
 +
# be able to control it with the lcdproc OUTPUT command
 +
OutputPort=no
 +
 
 +
# Specifies if the last line is pixel addressable or it controls an
 +
# underline effect. [default: true (= pixel addressable); legal: yes, no]
 +
#Lastline=true
 +
 
 +
# Specifies the size of the LCD.
 +
# In case of multiple combined displays, this should be the total size.
 +
Size=20x4
 +
 
 +
# For multiple combined displays: how many lines does each display have.
 +
# Vspan=2,2 means both displays have 2 lines.
 +
#vspan=2,2
 +
 
 +
# If you have an HD66712, a KS0073 or an other 'almost HD44780-compatible',
 +
# set this flag to get into extended mode (4-line linear).
 +
#ExtendedMode=yes
 +
 
 +
# In extended mode, on some controllers like the ST7036 (in 3 line mode)
 +
# the next line in DDRAM won't start 0x20 higher. [default: 0x20]
 +
#LineAddress=0x10
 +
 
 +
# Character map to to map ISO-8859-1 to the LCD's character set
 +
# [default: hd44780_default; legal: hd44780_default, hd44780_euro,
 +
#  ea_ks0073, sed1278f_0b ]
 +
CharMap=hd44780_default
 +
 
 +
# If your display is slow and cannot keep up with the flow of data from
 +
# LCDd, garbage can appear on the LCDd. Set this delay factor to 2 or 4
 +
# to increase the delays. Default: 1.
 +
#DelayMult=2
 +
 
 +
# Some displays (e.g. vdr-wakeup) need a message from the driver to that it
 +
# is still alive. When set to a value bigger then null the character in the
 +
# upper left corner is updated every <KeepAliveDisplay> seconds. Default: 0.
 +
#KeepAliveDisplay=0
 +
 
 +
# If you experience occasional garbage on your display you can use this
 +
# option as workaround. If set to a value bigger than null it forces a
 +
# full screen refresh <RefreshDiplay> seconds. Default: 0.
 +
#RefreshDisplay=5
 +
 
 +
# You can reduce the inserted delays by setting this to false.
 +
# On fast PCs it is possible your LCD does not respond correctly.
 +
# Default: true.
 +
DelayBus=true
 +
 
 +
# If you have a keypad you can assign keystrings to the keys.
 +
# See documentation for used terms and how to wire it.
 +
# For example to give directly connected key 4 the string "Enter", use:
 +
#  KeyDirect_4=Enter
 +
# For matrix keys use the X and Y coordinates of the key:
 +
#  KeyMatrix_1_3=Enter
 +
KeyMatrix_4_1=Enter
 +
KeyMatrix_4_2=Up
 +
KeyMatrix_4_3=Down
 +
KeyMatrix_4_4=Escape
 +
 
 +
 
 +
 
 +
## ICP A106 driver ##
 +
[icp_a106]
 +
Device=/dev/ttyS1
 +
 
 +
 
 +
 
 +
## Code Mercenaries IO-Warrior driver ##
 +
[IOWarrior]
 +
 
 +
# display dimensions
 +
Size=20x4
 +
 
 +
# serial number [exactly as listed by usbview]
 +
# (if not given, the 1st IOWarrior found gets used)
 +
#SerialNumber=00000674
 +
 
 +
# If you have an HD66712, a KS0073 or an other 'almost HD44780-compatible',
 +
# set this flag to get into extended mode (4-line linear).
 +
#ExtendedMode=yes
 +
 
 +
# Specifies if the last line is pixel addressable or it controls an
 +
# underline effect. [default: true (= pixel addressable); legal: yes, no]
 +
#Lastline=true
 +
 
 +
 
 +
 
 +
## Soundgraph/Ahanix/Silverstone/Uneed/Accent iMON driver ##
 +
[imon]
 +
 
 +
# select the device to use
 +
Device=/dev/lcd0
 +
 
 +
# display dimensions
 +
Size=16x2
 +
 
 +
 
 +
 
 +
## Soundgraph iMON LCD ##
 +
[imonlcd]
 +
# Specify which iMon protocol should be used [legal: 0=15c2:ffdc device,
 +
# 1=15c2:0038 device; default: 0]
 +
Protocol=0
 +
 
 +
# Set the exit behavior [legal: 0=leave shutdown message, 1=show the big clock,
 +
# 2=blank device; default: 1]
 +
#OnExit=2
 +
 
 +
# Select the output device to use [default: /dev/lcd0]
 +
Device=/dev/lcd0
 +
 
 +
# Select the displays contrast [default: 200; legal: 0-1000]
 +
Contrast=200
 +
 
 +
# Specify the size of the display in pixels [default: 96x16]
 +
#Size=96x16
 +
 
 +
# Set the backlight state [default: on; legal: on, off]
 +
Backlight=on
 +
 
 +
# Set the disc mode [legal: 0=spin the "slim" disc - two disc segments,
 +
# 1=their complement spinning; default: 0]
 +
#DiscMode=0
 +
 
 +
 
 +
 
 +
## IrMan driver ##
 +
[IrMan]
 +
# in case of trouble with IrMan, try the Lirc emulator for IrMan
 +
 
 +
# Select the input device to use
 +
#Device=/dev/irman
 +
 
 +
# Select the configuration file to use
 +
#Config=/etc/irman.cfg
 +
 
 +
 
 +
 
 +
## IRtrans driver ##
 +
[irtrans]
 +
 
 +
# Does the device have a backlight? [default: no; legal: yes, no]
 +
#Backlight=no
 +
 
 +
# IRTrans device to connect to [default: localhost]
 +
#Hostname=localhost
 +
 
 +
# display dimensions
 +
Size=16x2
 +
 
 +
 
 +
 
 +
## Joystick driver ##
 +
[joy]
 +
 
 +
# Select the input device to use [default: /dev/js0]
 +
Device=/dev/js0
 +
 
 +
# set the axis map
 +
Map_Axis1neg=Left
 +
Map_Axis1pos=Right
 +
Map_Axis2neg=Up
 +
Map_Axis2pos=Down
 +
 
 +
# set the button map
 +
Map_Button1=Enter
 +
Map_Button2=Escape
 +
 
 +
 
 +
 
 +
## LB216 driver ##
 +
[lb216]
 +
 
 +
# Select the output device to use [default: /dev/lcd]
 +
Device=/dev/lcd
 +
 
 +
# Set the initial brightness [default: 255; legal: 0 - 255]
 +
Brightness=255
 +
 
 +
# Set the communication speed [default: 9600; legal: 2400, 9600]
 +
Speed=9600
 +
 
 +
# Reinitialize the LCD's BIOS [default: no; legal: yes, no]
 +
Reboot=no
 +
 
 +
 
 +
 
 +
## LCDM001 driver ##
 +
[lcdm001]
 +
 
 +
Device=/dev/ttyS1
 +
 
 +
# keypad settings
 +
# Keyname      Function
 +
#              Normal context              Menu context
 +
# -------      --------------              ------------
 +
# PauseKey    Pause/Continue              Enter/select
 +
# BackKey      Back(Go to previous screen) Up/Left
 +
# ForwardKey  Forward(Go to next screen)  Down/Right
 +
# MainMenuKey  Open main menu              Exit/Cancel
 +
PauseKey=LeftKey
 +
BackKey=UpKey
 +
ForwardKey=DownKey
 +
MainMenuKey=RightKey
 +
 
 +
# You can rearrange the settings here.
 +
# If your device is broken, have a look at server/drivers/lcdm001.h
 +
 
 +
 
 +
 
 +
## HNE LCTerm driver ##
 +
[lcterm]
 +
Device=/dev/ttyS1
 +
Size=16x2
 +
 
 +
 
 +
 
 +
## LIRC input driver ##
 +
[lirc]
 +
 
 +
# Specify an alternative location of the lircrc file [default: ~/.lircrc]
 +
#lircrc=/etc/lircrc.lcdproc
 +
 
 +
# Must be the same as in your lircrc
 +
#prog=lcdd
 +
 
 +
 
 +
 
 +
## LIS MCE 2005 driver ##
 +
[lis]
 +
 
 +
# Set the initial brightness [default: 1000; legal: 0 - 1000]
 +
# 0-250 = 25%, 251-500 = 50%, 501-750 = 75%, 751-1000 = 100%
 +
#Brightness=1000
 +
 
 +
# Columns by lines [default: 20x2]
 +
#Size=20x2
 +
 
 +
# USB Vendor ID [default: 0x0403]
 +
# Change only if testing a compatible device.
 +
#VendorID=0x0403
 +
 
 +
# USB Product ID [default: 0x6001]
 +
# Change only if testing a compatible device.
 +
#ProductID=0x6001
 +
 
 +
 
 +
 
 +
##The driver for the VFD of the Medion MD8800 PC ##
 +
[MD8800]
 +
# device to use [default: /dev/ttyS1]
 +
#Device=/dev/ttyS1
 +
 
 +
# display size [default: 16x2]
 +
#Size=16x2
 +
 
 +
# Set the initial brightness [default: 1000; legal: 0 - 1000]
 +
Brightness=1000
 +
# Set the initial off-brightness [default: 0; legal: 0 - 1000]
 +
# This value is used when the display is normally
 +
# switched off in case LCDd is inactive
 +
OffBrightness=50
 +
 
 +
 
 +
 
 +
## MSI MS-6931 driver for displays in 1HU servers ##
 +
[ms6931]
 +
 
 +
# device to use [default: /dev/ttyS1]
 +
Device=/dev/ttyS1
 +
 
 +
# display size [default: 16x2]
 +
#Size=16x2
 +
 
 +
 
 +
 
 +
## MTC-S16209x driver ##
 +
[mtc_s16209x]
 +
 
 +
# Select the output device to use [default: /dev/lcd]
 +
Device=/dev/lcd
 +
 
 +
# Set the initial brightness [default: 255; legal: 0 - 255]
 +
Brightness=255
 +
 
 +
# Reinitialize the LCD's BIOS [default: no; legal: yes, no]
 +
Reboot=no
 +
 
 +
 
 +
 
 +
## Matrix Orbital driver ##
 +
[MtxOrb]
 +
 
 +
# Select the output device to use [default: /dev/lcd]
 +
Device=/dev/ttyS0
 +
 
 +
# Set the display size [default: 20x4]
 +
Size=20x4
 +
 
 +
# Set the display type [default: lcd; legal: lcd, lkd, vfd, vkd]
 +
Type=lkd
 +
 
 +
# Set the initial contrast [default: 480]
 +
# NOTE: The driver will ignore this if the display
 +
#      is a vfd or vkd as they don't have this feature
 +
Contrast=480
 +
 
 +
# Some old displays do not have an adjustable backlight but only can
 +
# switch the backlight on/off. If you experience randomly appearing block
 +
# characters, try setting this to false. [default: yes; legal: yes, no]
 +
hasAdjustableBacklight=no
 +
 
 +
# Set the initial brightness [default: 1000; legal: 0 - 1000]
 +
Brightness=1000
 +
# Set the initial off-brightness [default: 0; legal: 0 - 1000]
 +
# This value is used when the display is normally
 +
# switched off in case LCDd is inactive
 +
OffBrightness=0
 +
 
 +
# Set the communication speed [default: 19200; legal: 1200, 2400, 9600, 19200]
 +
Speed=19200
 +
 
 +
# The following table translates from MtxOrb key letters to logical key names.
 +
# By default no keys are mapped, meaning the keypad is not used at all.
 +
#KeyMap_A=Left
 +
#KeyMap_B=Right
 +
#KeyMap_C=Up
 +
#KeyMap_D=Down
 +
#KeyMap_E=Enter
 +
#KeyMap_F=Escape
 +
# See the [menu] section for an explanation of the key mappings
 +
 
 +
# You can find out which key of your display sends which
 +
# character by setting keypad_test_mode to yes and running
 +
# LCDd. LCDd will output all characters it receives.
 +
# Afterwards you can modify the settings above and set
 +
# keypad_set_mode to no again.
 +
keypad_test_mode=no
 +
 
 +
 
 +
 
 +
## mx5000 driver for LCD display on the Logitech MX5000 keyboard ##
 +
[mx5000]
 +
 
 +
# Select the output device to use [default: /dev/hiddev0]
 +
Device = /dev/hiddev0
 +
# Time to wait in ms after the refresh screen has been sent [default: 1000]
 +
WaitAfterRefresh = 1000
 +
 
 +
 
 +
 
 +
## Noritake VFD driver ##
 +
[NoritakeVFD]
 +
# device where the VFD is. Usual values are /dev/ttyS0 and /dev/ttyS1 [default: /dev/lcd]
 +
Device=/dev/ttyS0
 +
# Specifies the size of the LCD.
 +
Size=20x4
 +
# Set the initial brightness [default: 1000; legal: 0 - 1000]
 +
Brightness=1000
 +
# Set the initial off-brightness [default: 0; legal: 0 - 1000]
 +
# This value is used when the display is normally
 +
# switched off in case LCDd is inactive
 +
OffBrightness=50
 +
# set the serial port speed [default: 9600, legal: 1200, 2400, 9600, 19200, 115200]
 +
Speed=9600
 +
# Set serial data parity [default: 0 (None), legal: 0(=none), 1(=odd), 2(=even)]
 +
Parity=0
 +
# re-initialize the VFD [default: no; legal: yes, no]
 +
Reboot=no
 +
 
 +
 
 +
 
 +
## Mini-box.com picoLCD (usblcd) driver ##
 +
[picolcd]
 +
 
 +
# KeyTimeout is the time that LCDd spends waiting for a key press before cycling
 +
# through other duties.  Higher values make LCDd use less CPU time and make
 +
# key presses more detectable.  Lower values make LCDd more responsive but a
 +
# little prone to missing key presses.  500 (.5 second) is the default and a
 +
# balanced value.
 +
KeyTimeout=500
 +
 
 +
# Set the initial brightness [default: 1000; legal: 0 - 1000]
 +
Brightness=1000
 +
 
 +
# Set the initial contrast [default: 1000; legal: 0 - 1000]
 +
Contrast=1000
 +
 
 +
# Light the keys? i[default: on; legal: on, off]
 +
Keylights=on
 +
 
 +
# If Keylights is on, the you can unlight specific keys below:
 +
# Key0 is the directional pad.  Key1 - Key5 correspond to the F1 - F5 keys. 
 +
# There is no LED for the +/- keys.  This is a handy way to indicate to users
 +
# which keys are disabled.  [default: on; legal: on, off]
 +
Key0Light=on
 +
Key1Light=on
 +
Key2Light=on
 +
Key3Light=on
 +
Key4Light=on
 +
Key5Light=on
 +
 
 +
# Host name or IP address of the LIRC instance that is to receive IR codes
 +
# If not set, or set to an empty value, IR support is disabled.
 +
#LircHost=127.0.0.1
 +
 
 +
# UDP port on which LIRC is listening [default: 8765; legal: 1 - 65535]
 +
LircPort=8765
 +
 
 +
# Duration in jiffies of the synthesized sync pulse [default: 64; 0 to suppress]
 +
LircSync=64
 +
 
 +
# Duration in jiffies of the synthesized gap; 0 to suppress, default 2048.
 +
# This is really the fixed duration of an entire IR command; individual pulse/space
 +
# durations are deducted from this to determine the duration of the trailing gap.
 +
LircLength=2048
 +
 
 +
 
 +
 
 +
## Pyramid LCD driver ##
 +
[pyramid]
 +
 
 +
# device to connect to [default: /dev/lcd]
 +
Device=/dev/ttyUSB0
 +
 
 +
 
 +
 
 +
## Seiko Epson 1330 driver ##
 +
[sed1330]
 +
 
 +
# Port where the LPT is. Common values are 0x278, 0x378 and 0x3BC
 +
Port=0x378
 +
 
 +
# Type of LCD module (legal: G321D, G121C, G242C, G191D, G2446, SP14Q002)
 +
# Note: Currently only tested with G321D & SP14Q002.
 +
Type=G321D
 +
 
 +
# Width x Height of a character cell in pixels [legal: 6x7 - 8x16; default: 6x10]
 +
CellSize=6x10
 +
 
 +
# Select what type of connection [legal: classic, bitshaker; default: classic]
 +
ConnectionType=classic
 +
 
 +
 
 +
 
 +
## Seiko Epson 1520 driver ##
 +
[sed1520]
 +
 
 +
# Port where the LPT is. Usual values are 0x278, 0x378 and 0x3BC
 +
Port=0x378
 +
 
 +
 
 +
 
 +
## serial POS display driver ##
 +
[serialPOS]
 +
 
 +
# Device to use in serial modea [default: /dev/lcd]
 +
Device=/dev/lcd
 +
 
 +
# Specifies the size of the display in characters. [default: 16x2]
 +
Size=16x2
 +
 
 +
# Set the communication protocol to use with the POS display.
 +
# [default: AEDEX; legal: IEE, Epson, Emax, IBM, LogicControls, Ultimate]
 +
Type=AEDEX
 +
 
 +
# communication baud rate with the display [default: 9600; legal: 1200, 2400, 19200, 115200]
 +
Speed=9600
 +
 
 +
 
 +
 
 +
## Serial VFD driver ##
 +
## Drives various (see below) serial 5x7dot VFD's.  ##
 +
[serialVFD]
 +
 
 +
# Specifies the displaytype.[default: 0]
 +
# 0 NEC (FIPC8367 based) VFDs.
 +
# 1 KD Rev 2.1.
 +
# 2 Noritake VFDs (*).
 +
# 3 Futaba VFDs
 +
# 4 IEE S03601-95B
 +
# 5 IEE S03601-96-080 (*)
 +
# 6 Futaba NA202SD08FA (allmost IEE compatible)
 +
# 7 Samsung 20S207DA4 and 20S207DA6
 +
# 8 Nixdorf BA6x / VT100
 +
# (* most should work, not testet yet.)
 +
Type=0
 +
 
 +
# "no" if display connected serial, "yes" if connected parallel. [default: no(=serial)]
 +
use_parallel=no
 +
 
 +
# Number of Custom-Characters [default: displaytype dependent]
 +
#Custom-Characters=0
 +
 
 +
# Portaddress where the LPT is. Used in parallelmode only. Usual values are 0x278, 0x378 and 0x3BC
 +
Port=0x378
 +
 
 +
# Set parallel port timingdelay (us). Used in parallelmode only. [default: 2; legal: 0 - 255]
 +
#PortWait=2
 +
 
 +
# Device to use in serial mode. Usual values are /dev/ttyS0 and /dev/ttyS1
 +
Device=/dev/ttyS1
 +
 
 +
# Specifies the size of the VFD.
 +
Size=20x2
 +
 
 +
# Set the initial brightness [default: 1000; legal: 0 - 1000]
 +
# (4 steps 0-250, 251-500, 501-750, 751-1000)
 +
Brightness=1000
 +
# Set the initial off-brightness [default: 0; legal: 0 - 1000]
 +
# This value is used when the display is normally
 +
# switched off in case LCDd is inactive
 +
# (4 steps 0-250, 251-500, 501-750, 751-1000)
 +
OffBrightness=0
 +
 
 +
# set the serial port speed [default: 9600; legal: 1200, 2400, 9600, 19200, 115200]
 +
Speed=9600
 +
 
 +
# enable ISO 8859 1 compatibility [default: yes; legal: yes, no]
 +
#ISO_8859_1=yes
 +
 
 +
 
 +
 
 +
## shuttleVFD driver ##
 +
[shuttleVFD]
 +
# No options
 +
 
 +
 
 +
 
 +
## stv5730 driver ##
 +
[stv5730]
 +
 
 +
# Port the device is connected to [default: 0x378]
 +
Port=0x378
 +
 
 +
 
 +
 
 +
## SVGAlib driver ##
 +
[svga]
 +
 
 +
# svgalib mode to use [default: G320x240x256; legal: supported svgalib modes]
 +
#Mode=G640x480x256
 +
 
 +
# set display size [default: 20x4]
 +
Size=20x4
 +
 
 +
# Set the initial contrast [default: 500; legal: 0 - 1000]
 +
# Can be set but does not change anything internally
 +
Contrast=500
 +
 
 +
# Set the initial brightness [default: 1000; legal: 1 - 1000]
 +
Brightness=1000
 +
 
 +
# Set the initial off-brightness [default: 500; legal: 1 - 1000]
 +
# This value is used when the display is normally
 +
# switched off in case LCDd is inactive
 +
OffBrightness=500
 +
 
 +
 
 +
 
 +
## Text driver ##
 +
[text]
 +
# Set the display size [default: 20x4]
 +
Size=20x4
 +
 
 +
 
 +
 
 +
## Toshiba T6963 driver ##
 +
[t6963]
 +
 
 +
# set display size [default: 20x6]
 +
Size=20x6
 +
 
 +
# port to use [default: 0x378; legal: 0x200 - 0x400]
 +
Port=0x378
 +
 
 +
# Is ECP mode on? [default: yes; legal: yes, no]
 +
#ECPlpt=yes
 +
 
 +
# Use graphics? [default: no; legal: yes, no]
 +
#graphic=no
 +
 
 +
 
 +
 
 +
## Tyan Barebones LCD driver (GS10 & GS12 series) ##
 +
[tyan]
 +
 
 +
# Select the output device to use [default: /dev/lcd]
 +
Device=/dev/lcd
 +
 
 +
# Set the communication speed [default: 9600; legal: 4800, 9600]
 +
Speed=9600
 +
 
 +
# set display size [default: 16x2]
 +
Size=16x2
 +
 
 +
 
 +
 
 +
## ELV ula200 driver ##
 +
[ula200]
 +
 
 +
# Select the LCD size [default: 20x4]
 +
Size=20x4
 +
 
 +
# If you have a non standard keypad you can associate any keystrings to keys.
 +
# There are 6 input key in the CwLnx hardware that generate characters
 +
# from 'A' to 'F'.
 +
#
 +
# The following it the built-in default mapping hardcoded in the driver.
 +
# You can leave those unchanged if you have a standard keypad.
 +
# You can change it if you want to report other keystrings or have a non
 +
# standard keypad.
 +
# KeyMap_A=Up
 +
# KeyMap_B=Down
 +
# KeyMap_C=Left
 +
# KeyMap_D=Right
 +
# KeyMap_E=Enter
 +
# KeyMap_F=Escape
 +
 
 +
 
 +
 
 +
## Wirz SLI LCD driver ##
 +
[sli]
 +
 
 +
# Select the output device to use [default: /dev/lcd]
 +
Device=/dev/lcd
 +
 
 +
# Set the communication speed [default: 19200; legal: 1200, 2400, 9600, 19200, 38400, 57600, 115200]
 +
Speed=19200
 +
 
 +
 
 +
 
 +
## OnScreen Display using libxosd ##
 +
[xosd]
 +
 
 +
# set display size [default: 20x4]
 +
Size=20x4
 +
 
 +
# Offset in pixels from the top-left corner of the monitor [default: 0x0]
 +
Offset=200x200
 +
 
 +
# X font to use, in XLFD format, as given by "xfontsel"
 +
Font=-*-terminus-*-r-*-*-*-320-*-*-*-*-*
 +
 
 +
# EOF
 +
}}}
 
[[Category:log]]
 
[[Category:log]]

Latest revision as of 19:43, 27 August 2020

Use the default LCDd.conf that gets installed with the lcdproc package.

Change the line {{{ Driver=curses }}} to {{{ Driver=imon }}}

Create a file lirc.conf in /etc/modprobe.d with the following content, this will make sure the soundgraph imon is recognized as a vfd (rather than an lcd)

{{{ options lirc_imon display_type=1 }}}

{{{

  1. LCDd.conf -- configuration file for the LCDproc server daemon LCDd
  3. This file contains the configuration for the LCDd server.
  5. The format is ini-file-like. It is divided into sections that start at
  6. markers that look like [section]. Comments are all line-based comments,
  7. and are lines that start with '#' or ';'.
  9. The server has a 'central' section named [server]. For the menu there is
  10. a section called [menu]. Further each driver has a section which
  11. defines how the driver acts.
  13. The drivers are activated by specifiying them in a driver= line in the
  14. server section, like:
  17. This tells LCDd to use the curses driver.
  18. The first driver that is loaded and is capable of output defines the
  19. size of the display. The default driver to use is curses.
  20. If the driver is specified using the -d <driver> command line option,
  21. the Driver= options in the config file are ignored.
  23. The drivers read their own options from the respective sections.


    1. Server section with all kinds of settings for the LCDd server ##

[server]

  1. Where can we find the driver modules ?
  2. IMPORTANT: Make sure to change this setting to reflect your
  3. specific setup! Otherwise LCDd won't be able to find
  4. the driver modules and will thus not be able to
  5. function properly.
  6. NOTE: Always place a slash as last character !

DriverPath=/usr/lib/lcdproc/

  1. Tells the server to load the given drivers. Multiple lines can be given.
  2. The name of the driver is case sensitive and determines the section
  3. where to look for further configuration options of the specific driver
  4. as well as the name of the dynamic driver module to load at runtime.
  5. The latter one can be changed by giving af File= directive in the
  6. driver specific section.
  8. The following drivers are supported:
  9. bayrad, CFontz, CFontz633, CFontzPacket, curses, CwLnx, ea65,
  10. EyeboxOne, g15, glcdlib, glk, hd44780, icp_a106, imon, imonlcd, IOWarrior,
  11. irman, joy, lb216, lcdm001, lcterm, lirc, lis, MD8800, ms6931, mtc_s16209x,
  12. MtxOrb, mx5000, NoritakeVFD, picolcd, pyramid, sed1330, sed1520, serialPOS,
  13. serialVFD, shuttleVFD, sli, stv5730, svga, t6963, text, tyan, ula200,
  14. xosd

Driver=imon

  1. Tells the driver to bind to the given interface

Bind=127.0.0.1

  1. Listen on this specified port; defaults to 13666.

Port=13666

  1. Sets the reporting level; defaults to 2 (warnings and errors only).
  2. ReportLevel=3
  1. Should we report to syslog instead of stderr ? [default: no; legal: yes, no]
  2. ReportToSyslog=yes
  1. User to run as. LCDd will drop its root priviledges, if any,
  2. and run as this user instead.

User=nobody

  1. The server will stay in the foreground if set to true.
  2. Foreground=no
  1. Hello message: each entry represents a display line; default: builtin
  2. Hello=" Welcome to"
  3. Hello=" LCDproc!"
  1. GoodBye message: each entry represents a display line; default: builtin
  2. GoodBye="Thanks for using"
  3. GoodBye=" LCDproc!"
  1. Sets the default time in seconds to displays a screen.

WaitTime=5

  1. If yes, the the serverscreen will be rotated as a usual info screen. If no,
  2. it will be a background screen, only visible when no other screens are
  3. active. The special value 'blank' is similar to no, but only a blank screen
  4. is displayed. [default: on; legal: on, off, blank]
  5. ServerScreen=no
  1. Set master backlight setting. If set to 'open' a client may control the
  2. backlight for its own screens (only). [default: open; legal: off, open, on]
  3. Backlight=open
  1. Set master heartbeat setting. If set to 'open' a client may control the
  2. heartbeat for its own screens (only). [default: open; legal: off, open, on]
  3. Heartbeat=open
  1. set title scrolling speed [default: 10; legal: 0-10]
  2. TitleSpeed=10
  1. The "...Key=" lines define what the server does with keypresses that
  2. don't go to any client.
  3. These are the defaults:

ToggleRotateKey=Enter PrevScreenKey=Left NextScreenKey=Right

  1. ScrollUpKey=Up
  2. ScrollDownKey=Down
  1. If you have only 4 keys, you can choose to use this:
  2. ToggleRotateKey=Enter
  3. PrevScreenKey=Up
  4. NextScreenKey=Down
  1. If you have only 3 keys, you can choose to use this:
  2. ToggleRotateKey=Enter
  3. PrevScreenKey=Up


    1. The menu section. The menu is an internal LCDproc client. ##

[menu]

  1. You can configure what keys the menu should use. Note that the MenuKey
  2. will be reserved exclusively, the others work in shared mode.
  1. The following works excellent with 4 keys or more.

MenuKey=Escape EnterKey=Enter UpKey=Up DownKey=Down

  1. If you have 6 keys you may define these as well
  2. LeftKey=Left
  3. RightKey=Right
  1. If you have only 3 keys, you could use something like this:
  2. MenuKey=Escape
  3. EnterKey=Enter
  4. DownKey=Down


      1. Driver sections are below this line, in alphabetical order ###


    1. EMAC BayRAD driver ##

[bayrad]

  1. Select the output device to use [default: /dev/lcd]

Device=/dev/lcd

  1. Set the communication speed [default: 9600; legal: 1200, 2400, 9600, 19200]

Speed=9600


    1. CrystalFontz driver (for CF632 & CF634) ##

[CFontz]

  1. Select the output device to use [default: /dev/lcd]

Device=/dev/ttyS0

  1. Select the LCD size [default: 20x4]

Size=20x4

  1. Set the initial contrast [default: 560; legal: 0 - 1000]

Contrast=350

  1. Set the initial brightness [default: 1000; legal: 0 - 1000]

Brightness=1000

  1. Set the initial off-brightness [default: 0; legal: 0 - 1000]
  2. This value is used when the display is normally
  3. switched off in case LCDd is inactive

OffBrightness=0

  1. Set the communication speed [default: 9600; legal: 1200, 2400, 9600, 19200 or 115200]

Speed=9600

  1. Set the firmware version (New means >= 2.0) [default: no; legal: yes, no]

NewFirmware=no

  1. Reinitialize the LCD's BIOS [default: no; legal: yes, no]
  2. normally you shouldn't need this

Reboot=no


    1. CrystalFontz633 driver (for CF633 only) ##

[CFontz633]

  1. Select the output device to use [default: /dev/lcd]

Device=/dev/ttyS0

  1. Select the LCD type (size) [default: 16x2]

Size=16x2

  1. Set the initial contrast [default: 560; legal: 0 - 1000]

Contrast=350

  1. Set the initial brightness [default: 1000; legal: 0 - 1000]

Brightness=1000

  1. Set the initial off-brightness [default: 0; legal: 0 - 1000]
  2. This value is used when the display is normally
  3. switched off in case LCDd is inactive

OffBrightness=50

  1. Set the communication speed [default: 9600; legal: 1200, 2400, 9600, 19200, 115200]

Speed=19200

  1. Set the firmware version (New means >= 2.0) [default: no; legal: yes, no]
  2. Currently this flag is not in use, there is no such thing as NewFirmware. ;=)
  3. NewFirmware=no
  4. Reinitialize the LCD's BIOS [default: no; legal: yes, no]
  5. I want to reboot the LCD to make sure we start from a known state

Reboot=yes


    1. CrystalFontz packet driver (for CF631, CF633 & CF635) ##

[CFontzPacket]

  1. Select the LCD model [default: 633; legal: 631, 633, 635]

Model=635

  1. Select the output device to use [default: /dev/lcd]

Device=/dev/ttyUSB0

  1. Select the LCD size [default: depending on model: 635: 20x4, 631: 20x2, 633: 16x2]

Size=20x4

  1. Set the initial contrast [default: 560; legal: 0 - 1000]

Contrast=350

  1. Set the initial brightness [default: 1000; legal: 0 - 1000]

Brightness=1000

  1. Set the initial off-brightness [default: 0; legal: 0 - 1000]
  2. This value is used when the display is normally
  3. switched off in case LCDd is inactive

OffBrightness=50

  1. Set the communication speed [default: 9600; legal: 1200, 2400, 9600, 19200, 115200]

Speed=115200

  1. Set the firmware version (New means >= 2.0) [default: no; legal: yes, no]
  2. Currently this flag is not in use, there is no such thing as NewFirmware. ;=)
  3. NewFirmware=no
  4. Reinitialize the LCD's BIOS [default: no; legal: yes, no]
  5. I want to reboot the LCD to make sure we start from a known state

Reboot=yes


    1. Curses driver ##

[curses]

  1. color settings
  2. foreground color [default: blue]

Foreground=blue

  1. background color when "backlight" is off [default: cyan]

Background=cyan

  1. background color when "backlight" is on [default: red]

Backlight=red

  1. display size [default: 20x4]

Size=20x4

  1. What position (X,Y) to start the left top corner at...
  2. Default: (7,7)

TopLeftX=7 TopLeftY=7

  1. use ASC symbols for icons & bars [default: no; legal, yes, no]

UseACS=no

  1. draw Border [default: yes; legal: yes, no]

DrawBorder=yes


    1. Cwlinux driver ##

[CwLnx]

  1. Select the LCD model [default: 12232; legal: 12232, 12832, 1602]

Model=12232

  1. Select the output device to use [default: /dev/lcd]

Device=/dev/ttyUSB0

  1. Select the LCD size [default: depending on model: 12232: 20x4, 12832: 21x4, 1602: 16x2]

Size=20x4

  1. Set the communication speed [default: 19200; legal: 9600, 19200]

Speed=19200

  1. Reinitialize the LCD's BIOS [default: no; legal: yes, no]
  2. normally you shouldn't need this

Reboot=no

  1. If you have a keypad connected. Keypad layout is currently not
  2. configureable from the config file.

Keypad=yes

  1. If you have a non-standard keypad you can associate any keystrings to keys.
  2. There are 6 input keys in the CwLnx hardware that generate characters
  3. from 'A' to 'F'.
  5. The following is the built-in default mapping hardcoded in the driver.
  6. You can leave those unchanged if you have a standard keypad.
  7. You can change it if you want to report other keystrings or have a non
  8. standard keypad.
  9. KeyMap_A=Up
  10. KeyMap_B=Down
  11. KeyMap_C=Left
  12. KeyMap_D=Right
  13. KeyMap_E=Enter
  14. KeyMap_F=Escape
  1. keypad_test_mode permits to test keypad assignement
  2. Default value is no
  3. keypad_test_mode=yes


    1. ea65 driver for the display in AOpen XC Cube AV EA65 media barebones ##

[ea65]

  1. Device is fixed /dev/ttyS1
  2. Width and Height are fixed 9x1
  1. As the VFD is self luminescent we don't have a backlight
  2. But we can use the backlight functions to control the front LEDs
  3. Brightness 0 to 299 -> LEDs off
  4. Brightness 300 to 699 -> LEDs half bright
  5. Brightness 700 to 1000 -> LEDs full bright

Brightness=500

  1. OffBrightness is the the value used for the 'backlight off' state

OffBrightness=0


    1. EyeboxOne driver ##

[EyeboxOne]

  1. Select the output device to use [default: /dev/ttyS1]
  2. Device=/dev/cua01

Device=/dev/ttyS1

  1. Set the display size [default: 20x4]

Size=20x4

  1. Switch on the backlight? [default: yes]

Backlight=yes

  1. Switch on the cursor? [default: no]

Cursor=no

  1. Set the communication speed [default: 19200; legal: 1200, 2400, 9600, 19200]

Speed=19200

  1. Enter Key is a \r character, so it's hardcoded in the driver

LeftKey=D RightKey=C UpKey=A DownKey=B EscapeKey=P

  1. You can find out which key of your display sends which
  2. character by setting keypad_test_mode to yes and running
  3. LCDd. LCDd will output all characters it receives.
  4. Afterwards you can modify the settings above and set
  5. keypad_set_mode to no again.

keypad_test_mode=no


    1. g15 driver for Logitech G15 Keyboard LCDs ##

[g15]

  1. Display size (currently unused)

size=20x5


    1. glcdlib meta driver for graphical LCDs ##

[glcdlib]

    1. mandatory:
  1. which graphical display supported by graphlcd-base to use [default: image]
  2. (see /etc/graphlcd.conf for possible drivers)

Driver=noritake800

  1. no=use graphlcd bitmap fonts (they have only one size / font file)
  2. yes=use fonts supported by FreeType2 (needs Freetype2 support in libglcdprocdriver and its dependants)

UseFT2=yes

  1. text resolution in fixed width characters [default: 16x4]
  2. (if it won't fit according to available physical pixel resolutioni
  3. and the minimum available font face size in pixels, then
  4. 'DebugBorder' will automatically be turned on)

TextResolution=20x4

  1. path to font file to use

FontFile=/usr/share/fonts/corefonts/courbd.ttf

    1. these only apply if UseFT2=yes:
  1. character encoding to use

CharEncoding=iso8859-2

  1. minumum size in pixels in which fonts should be rendered

MinFontFaceSize=7x12

    1. optional:

Brightness=50 # Brightness (in %) if applicable Contrast=50 # Contrast (in %) if applicable Backlight=no # Backlight if applicable UpsideDown=no # flip image upside down Invert=no # invert light/dark pixels ShowDebugFrame=no # turns on/off 1 pixel thick debugging 

                               # border whithin the usable text area,
                               # for setting up TextResolution and
                               # MinFontFaceSize (if using FT2);

ShowBigBorder=no # border around the unused area ShowThinBorder=yes # border around the unused area PixelShiftX=0 PixelShiftY=2


    1. Matrix Orbital GLK driver ##

[glk]

  1. select the serial device to use [default: /dev/lcd]

Device=/dev/lcd

  1. set the initial contrast value [default: 560; legal: 0 - 1000]

Contrast=560

  1. set the serial port speed [default: 19200; legal: 9600, 19200, 38400]

Speed=19200


    1. Hitachi HD44780 driver ##

[hd44780]

  1. Select what type of connection. See documentation for types.

ConnectionType=4bit

  1. Port where the LPT is [ususal: 0x278, 0x378 and 0x3BC]

Port=0x378

  1. Device of the serial interface [default: /dev/lcd]

Device=/dev/ttyS0

  1. Bitrate of the serial port (0 for interface default)

Speed=0

  1. If you have a keypad connected.
  2. You may also need to configure the keypad layout further on in this file.

Keypad=no

  1. Set the initial contrast (bwctusb and lcd2usb) [default: 500; legal: 0 - 1000]

Contrast=0

  1. Set brightness of the backlight (lcd2usb only) [default: 0; legal 0 - 1000]
  2. Brightness=1000
  3. OffBrightness=0
  1. If you have a switchable backlight.

Backlight=no

  1. If you have the additional output port ("bargraph") and you want to
  2. be able to control it with the lcdproc OUTPUT command

OutputPort=no

  1. Specifies if the last line is pixel addressable or it controls an
  2. underline effect. [default: true (= pixel addressable); legal: yes, no]
  3. Lastline=true
  1. Specifies the size of the LCD.
  2. In case of multiple combined displays, this should be the total size.

Size=20x4

  1. For multiple combined displays: how many lines does each display have.
  2. Vspan=2,2 means both displays have 2 lines.
  3. vspan=2,2
  1. If you have an HD66712, a KS0073 or an other 'almost HD44780-compatible',
  2. set this flag to get into extended mode (4-line linear).
  3. ExtendedMode=yes
  1. In extended mode, on some controllers like the ST7036 (in 3 line mode)
  2. the next line in DDRAM won't start 0x20 higher. [default: 0x20]
  3. LineAddress=0x10
  1. Character map to to map ISO-8859-1 to the LCD's character set
  2. [default: hd44780_default; legal: hd44780_default, hd44780_euro,
  3. ea_ks0073, sed1278f_0b ]

CharMap=hd44780_default

  1. If your display is slow and cannot keep up with the flow of data from
  2. LCDd, garbage can appear on the LCDd. Set this delay factor to 2 or 4
  3. to increase the delays. Default: 1.
  4. DelayMult=2
  1. Some displays (e.g. vdr-wakeup) need a message from the driver to that it
  2. is still alive. When set to a value bigger then null the character in the
  3. upper left corner is updated every <KeepAliveDisplay> seconds. Default: 0.
  4. KeepAliveDisplay=0
  1. If you experience occasional garbage on your display you can use this
  2. option as workaround. If set to a value bigger than null it forces a
  3. full screen refresh <RefreshDiplay> seconds. Default: 0.
  4. RefreshDisplay=5
  1. You can reduce the inserted delays by setting this to false.
  2. On fast PCs it is possible your LCD does not respond correctly.
  3. Default: true.

DelayBus=true

  1. If you have a keypad you can assign keystrings to the keys.
  2. See documentation for used terms and how to wire it.
  3. For example to give directly connected key 4 the string "Enter", use:
  4. KeyDirect_4=Enter
  5. For matrix keys use the X and Y coordinates of the key:
  6. KeyMatrix_1_3=Enter

KeyMatrix_4_1=Enter KeyMatrix_4_2=Up KeyMatrix_4_3=Down KeyMatrix_4_4=Escape


    1. ICP A106 driver ##

[icp_a106] Device=/dev/ttyS1


    1. Code Mercenaries IO-Warrior driver ##

[IOWarrior]

  1. display dimensions

Size=20x4

  1. serial number [exactly as listed by usbview]
  2. (if not given, the 1st IOWarrior found gets used)
  3. SerialNumber=00000674
  1. If you have an HD66712, a KS0073 or an other 'almost HD44780-compatible',
  2. set this flag to get into extended mode (4-line linear).
  3. ExtendedMode=yes
  1. Specifies if the last line is pixel addressable or it controls an
  2. underline effect. [default: true (= pixel addressable); legal: yes, no]
  3. Lastline=true


    1. Soundgraph/Ahanix/Silverstone/Uneed/Accent iMON driver ##

[imon]

  1. select the device to use

Device=/dev/lcd0

  1. display dimensions

Size=16x2


    1. Soundgraph iMON LCD ##

[imonlcd]

  1. Specify which iMon protocol should be used [legal: 0=15c2:ffdc device,
  2. 1=15c2:0038 device; default: 0]

Protocol=0

  1. Set the exit behavior [legal: 0=leave shutdown message, 1=show the big clock,
  2. 2=blank device; default: 1]
  3. OnExit=2
  1. Select the output device to use [default: /dev/lcd0]

Device=/dev/lcd0

  1. Select the displays contrast [default: 200; legal: 0-1000]

Contrast=200

  1. Specify the size of the display in pixels [default: 96x16]
  2. Size=96x16
  1. Set the backlight state [default: on; legal: on, off]

Backlight=on

  1. Set the disc mode [legal: 0=spin the "slim" disc - two disc segments,
  2. 1=their complement spinning; default: 0]
  3. DiscMode=0


    1. IrMan driver ##

[IrMan]

  1. in case of trouble with IrMan, try the Lirc emulator for IrMan
  1. Select the input device to use
  2. Device=/dev/irman
  1. Select the configuration file to use
  2. Config=/etc/irman.cfg


    1. IRtrans driver ##

[irtrans]

  1. Does the device have a backlight? [default: no; legal: yes, no]
  2. Backlight=no
  1. IRTrans device to connect to [default: localhost]
  2. Hostname=localhost
  1. display dimensions

Size=16x2


    1. Joystick driver ##

[joy]

  1. Select the input device to use [default: /dev/js0]

Device=/dev/js0

  1. set the axis map

Map_Axis1neg=Left Map_Axis1pos=Right Map_Axis2neg=Up Map_Axis2pos=Down

  1. set the button map

Map_Button1=Enter Map_Button2=Escape


    1. LB216 driver ##

[lb216]

  1. Select the output device to use [default: /dev/lcd]

Device=/dev/lcd

  1. Set the initial brightness [default: 255; legal: 0 - 255]

Brightness=255

  1. Set the communication speed [default: 9600; legal: 2400, 9600]

Speed=9600

  1. Reinitialize the LCD's BIOS [default: no; legal: yes, no]

Reboot=no


    1. LCDM001 driver ##

[lcdm001]

Device=/dev/ttyS1

  1. keypad settings
  2. Keyname Function
  3. Normal context Menu context
  4. ------- -------------- ------------
  5. PauseKey Pause/Continue Enter/select
  6. BackKey Back(Go to previous screen) Up/Left
  7. ForwardKey Forward(Go to next screen) Down/Right
  8. MainMenuKey Open main menu Exit/Cancel

PauseKey=LeftKey BackKey=UpKey ForwardKey=DownKey MainMenuKey=RightKey

  1. You can rearrange the settings here.
  2. If your device is broken, have a look at server/drivers/lcdm001.h


    1. HNE LCTerm driver ##

[lcterm] Device=/dev/ttyS1 Size=16x2


    1. LIRC input driver ##

[lirc]

  1. Specify an alternative location of the lircrc file [default: ~/.lircrc]
  2. lircrc=/etc/lircrc.lcdproc
  1. Must be the same as in your lircrc
  2. prog=lcdd


    1. LIS MCE 2005 driver ##

[lis]

  1. Set the initial brightness [default: 1000; legal: 0 - 1000]
  2. 0-250 = 25%, 251-500 = 50%, 501-750 = 75%, 751-1000 = 100%
  3. Brightness=1000
  1. Columns by lines [default: 20x2]
  2. Size=20x2
  1. USB Vendor ID [default: 0x0403]
  2. Change only if testing a compatible device.
  3. VendorID=0x0403
  1. USB Product ID [default: 0x6001]
  2. Change only if testing a compatible device.
  3. ProductID=0x6001


    1. The driver for the VFD of the Medion MD8800 PC ##

[MD8800]

  1. device to use [default: /dev/ttyS1]
  2. Device=/dev/ttyS1
  1. display size [default: 16x2]
  2. Size=16x2
  1. Set the initial brightness [default: 1000; legal: 0 - 1000]

Brightness=1000

  1. Set the initial off-brightness [default: 0; legal: 0 - 1000]
  2. This value is used when the display is normally
  3. switched off in case LCDd is inactive

OffBrightness=50


    1. MSI MS-6931 driver for displays in 1HU servers ##

[ms6931]

  1. device to use [default: /dev/ttyS1]

Device=/dev/ttyS1

  1. display size [default: 16x2]
  2. Size=16x2


    1. MTC-S16209x driver ##

[mtc_s16209x]

  1. Select the output device to use [default: /dev/lcd]

Device=/dev/lcd

  1. Set the initial brightness [default: 255; legal: 0 - 255]

Brightness=255

  1. Reinitialize the LCD's BIOS [default: no; legal: yes, no]

Reboot=no


    1. Matrix Orbital driver ##

[MtxOrb]

  1. Select the output device to use [default: /dev/lcd]

Device=/dev/ttyS0

  1. Set the display size [default: 20x4]

Size=20x4

  1. Set the display type [default: lcd; legal: lcd, lkd, vfd, vkd]

Type=lkd

  1. Set the initial contrast [default: 480]
  2. NOTE: The driver will ignore this if the display
  3. is a vfd or vkd as they don't have this feature

Contrast=480

  1. Some old displays do not have an adjustable backlight but only can
  2. switch the backlight on/off. If you experience randomly appearing block
  3. characters, try setting this to false. [default: yes; legal: yes, no]

hasAdjustableBacklight=no

  1. Set the initial brightness [default: 1000; legal: 0 - 1000]

Brightness=1000

  1. Set the initial off-brightness [default: 0; legal: 0 - 1000]
  2. This value is used when the display is normally
  3. switched off in case LCDd is inactive

OffBrightness=0

  1. Set the communication speed [default: 19200; legal: 1200, 2400, 9600, 19200]

Speed=19200

  1. The following table translates from MtxOrb key letters to logical key names.
  2. By default no keys are mapped, meaning the keypad is not used at all.
  3. KeyMap_A=Left
  4. KeyMap_B=Right
  5. KeyMap_C=Up
  6. KeyMap_D=Down
  7. KeyMap_E=Enter
  8. KeyMap_F=Escape
  9. See the [menu] section for an explanation of the key mappings
  1. You can find out which key of your display sends which
  2. character by setting keypad_test_mode to yes and running
  3. LCDd. LCDd will output all characters it receives.
  4. Afterwards you can modify the settings above and set
  5. keypad_set_mode to no again.

keypad_test_mode=no


    1. mx5000 driver for LCD display on the Logitech MX5000 keyboard ##

[mx5000]

  1. Select the output device to use [default: /dev/hiddev0]

Device = /dev/hiddev0

  1. Time to wait in ms after the refresh screen has been sent [default: 1000]

WaitAfterRefresh = 1000


    1. Noritake VFD driver ##

[NoritakeVFD]

  1. device where the VFD is. Usual values are /dev/ttyS0 and /dev/ttyS1 [default: /dev/lcd]

Device=/dev/ttyS0

  1. Specifies the size of the LCD.

Size=20x4

  1. Set the initial brightness [default: 1000; legal: 0 - 1000]

Brightness=1000

  1. Set the initial off-brightness [default: 0; legal: 0 - 1000]
  2. This value is used when the display is normally
  3. switched off in case LCDd is inactive

OffBrightness=50

  1. set the serial port speed [default: 9600, legal: 1200, 2400, 9600, 19200, 115200]

Speed=9600

  1. Set serial data parity [default: 0 (None), legal: 0(=none), 1(=odd), 2(=even)]

Parity=0

  1. re-initialize the VFD [default: no; legal: yes, no]

Reboot=no


    1. Mini-box.com picoLCD (usblcd) driver ##

[picolcd]

  1. KeyTimeout is the time that LCDd spends waiting for a key press before cycling
  2. through other duties. Higher values make LCDd use less CPU time and make
  3. key presses more detectable. Lower values make LCDd more responsive but a
  4. little prone to missing key presses. 500 (.5 second) is the default and a
  5. balanced value.

KeyTimeout=500

  1. Set the initial brightness [default: 1000; legal: 0 - 1000]

Brightness=1000

  1. Set the initial contrast [default: 1000; legal: 0 - 1000]

Contrast=1000

  1. Light the keys? i[default: on; legal: on, off]

Keylights=on

  1. If Keylights is on, the you can unlight specific keys below:
  2. Key0 is the directional pad. Key1 - Key5 correspond to the F1 - F5 keys.
  3. There is no LED for the +/- keys. This is a handy way to indicate to users
  4. which keys are disabled. [default: on; legal: on, off]

Key0Light=on Key1Light=on Key2Light=on Key3Light=on Key4Light=on Key5Light=on

  1. Host name or IP address of the LIRC instance that is to receive IR codes
  2. If not set, or set to an empty value, IR support is disabled.
  3. LircHost=127.0.0.1
  1. UDP port on which LIRC is listening [default: 8765; legal: 1 - 65535]

LircPort=8765

  1. Duration in jiffies of the synthesized sync pulse [default: 64; 0 to suppress]

LircSync=64

  1. Duration in jiffies of the synthesized gap; 0 to suppress, default 2048.
  2. This is really the fixed duration of an entire IR command; individual pulse/space
  3. durations are deducted from this to determine the duration of the trailing gap.

LircLength=2048


    1. Pyramid LCD driver ##

[pyramid]

  1. device to connect to [default: /dev/lcd]

Device=/dev/ttyUSB0


    1. Seiko Epson 1330 driver ##

[sed1330]

  1. Port where the LPT is. Common values are 0x278, 0x378 and 0x3BC

Port=0x378

  1. Type of LCD module (legal: G321D, G121C, G242C, G191D, G2446, SP14Q002)
  2. Note: Currently only tested with G321D & SP14Q002.

Type=G321D

  1. Width x Height of a character cell in pixels [legal: 6x7 - 8x16; default: 6x10]

CellSize=6x10

  1. Select what type of connection [legal: classic, bitshaker; default: classic]

ConnectionType=classic


    1. Seiko Epson 1520 driver ##

[sed1520]

  1. Port where the LPT is. Usual values are 0x278, 0x378 and 0x3BC

Port=0x378


    1. serial POS display driver ##

[serialPOS]

  1. Device to use in serial modea [default: /dev/lcd]

Device=/dev/lcd

  1. Specifies the size of the display in characters. [default: 16x2]

Size=16x2

  1. Set the communication protocol to use with the POS display.
  2. [default: AEDEX; legal: IEE, Epson, Emax, IBM, LogicControls, Ultimate]

Type=AEDEX

  1. communication baud rate with the display [default: 9600; legal: 1200, 2400, 19200, 115200]

Speed=9600


    1. Serial VFD driver ##
    2. Drives various (see below) serial 5x7dot VFD's. ##

[serialVFD]

  1. Specifies the displaytype.[default: 0]
  2. 0 NEC (FIPC8367 based) VFDs.
  3. 1 KD Rev 2.1.
  4. 2 Noritake VFDs (*).
  5. 3 Futaba VFDs
  6. 4 IEE S03601-95B
  7. 5 IEE S03601-96-080 (*)
  8. 6 Futaba NA202SD08FA (allmost IEE compatible)
  9. 7 Samsung 20S207DA4 and 20S207DA6
  10. 8 Nixdorf BA6x / VT100
  11. (* most should work, not testet yet.)

Type=0

  1. "no" if display connected serial, "yes" if connected parallel. [default: no(=serial)]

use_parallel=no

  1. Number of Custom-Characters [default: displaytype dependent]
  2. Custom-Characters=0
  1. Portaddress where the LPT is. Used in parallelmode only. Usual values are 0x278, 0x378 and 0x3BC

Port=0x378

  1. Set parallel port timingdelay (us). Used in parallelmode only. [default: 2; legal: 0 - 255]
  2. PortWait=2
  1. Device to use in serial mode. Usual values are /dev/ttyS0 and /dev/ttyS1

Device=/dev/ttyS1

  1. Specifies the size of the VFD.

Size=20x2

  1. Set the initial brightness [default: 1000; legal: 0 - 1000]
  2. (4 steps 0-250, 251-500, 501-750, 751-1000)

Brightness=1000

  1. Set the initial off-brightness [default: 0; legal: 0 - 1000]
  2. This value is used when the display is normally
  3. switched off in case LCDd is inactive
  4. (4 steps 0-250, 251-500, 501-750, 751-1000)

OffBrightness=0

  1. set the serial port speed [default: 9600; legal: 1200, 2400, 9600, 19200, 115200]

Speed=9600

  1. enable ISO 8859 1 compatibility [default: yes; legal: yes, no]
  2. ISO_8859_1=yes


    1. shuttleVFD driver ##

[shuttleVFD]

  1. No options


    1. stv5730 driver ##

[stv5730]

  1. Port the device is connected to [default: 0x378]

Port=0x378


    1. SVGAlib driver ##

[svga]

  1. svgalib mode to use [default: G320x240x256; legal: supported svgalib modes]
  2. Mode=G640x480x256
  1. set display size [default: 20x4]

Size=20x4

  1. Set the initial contrast [default: 500; legal: 0 - 1000]
  2. Can be set but does not change anything internally

Contrast=500

  1. Set the initial brightness [default: 1000; legal: 1 - 1000]

Brightness=1000

  1. Set the initial off-brightness [default: 500; legal: 1 - 1000]
  2. This value is used when the display is normally
  3. switched off in case LCDd is inactive

OffBrightness=500


    1. Text driver ##

[text]

  1. Set the display size [default: 20x4]

Size=20x4


    1. Toshiba T6963 driver ##

[t6963]

  1. set display size [default: 20x6]

Size=20x6

  1. port to use [default: 0x378; legal: 0x200 - 0x400]

Port=0x378

  1. Is ECP mode on? [default: yes; legal: yes, no]
  2. ECPlpt=yes
  1. Use graphics? [default: no; legal: yes, no]
  2. graphic=no


    1. Tyan Barebones LCD driver (GS10 & GS12 series) ##

[tyan]

  1. Select the output device to use [default: /dev/lcd]

Device=/dev/lcd

  1. Set the communication speed [default: 9600; legal: 4800, 9600]

Speed=9600

  1. set display size [default: 16x2]

Size=16x2


    1. ELV ula200 driver ##

[ula200]

  1. Select the LCD size [default: 20x4]

Size=20x4

  1. If you have a non standard keypad you can associate any keystrings to keys.
  2. There are 6 input key in the CwLnx hardware that generate characters
  3. from 'A' to 'F'.
  5. The following it the built-in default mapping hardcoded in the driver.
  6. You can leave those unchanged if you have a standard keypad.
  7. You can change it if you want to report other keystrings or have a non
  8. standard keypad.
  9. KeyMap_A=Up
  10. KeyMap_B=Down
  11. KeyMap_C=Left
  12. KeyMap_D=Right
  13. KeyMap_E=Enter
  14. KeyMap_F=Escape


    1. Wirz SLI LCD driver ##

[sli]

  1. Select the output device to use [default: /dev/lcd]

Device=/dev/lcd

  1. Set the communication speed [default: 19200; legal: 1200, 2400, 9600, 19200, 38400, 57600, 115200]

Speed=19200


    1. OnScreen Display using libxosd ##

[xosd]

  1. set display size [default: 20x4]

Size=20x4

  1. Offset in pixels from the top-left corner of the monitor [default: 0x0]

Offset=200x200

  1. X font to use, in XLFD format, as given by "xfontsel"

Font=-*-terminus-*-r-*-*-*-320-*-*-*-*-*

  1. EOF

}}}

Retrieved from "https://wiki.dirkjanswagerman.nl/index.php?title=LCDd&oldid=7420"